need help from all you smart people

[crom A zone]

ok i have a 2005 eiger can never get my air box sealed and not leaking with my snorkles.
what you all think about taking box out and put filter at the top of snorkle   good or bad idea let me all no what u think   thank you in advanced

[kawasakimojaverider]

i did on my old truck

[crom A zone]

how did it work  and  did any one do it on a quad

[FastestCub305]

sp ypur going to remove the airbox and connet the snorkel to the carb?

[dj_pizzim]

remember the airbox acts as the last stop before the motor so if water goes down the snorkels it can pool up in the box a little before going in the motor.  I know people have done it with no problems.  It a matter of choice really

[TRX450R_Racer]

You can add a trap to the snorkle like in the drain for a sink.

I thought I wasn't going to be able to help because you asked for the smart people.

[brocker]

Won't that screw up your jetting by running a full open air filter?

[grizzlyranger]

i dont know about the jettin but i know somebody did the same thing on a rincon and it works perfect and this guy water rides all the time. 

[crom A zone]

all u have to do about the jetting is open up the fuel  now i am at a 135 main jet i would prob be up around     a 155 to 170 main jet  its a crazy jump but its gotta be equle with how much fuel u have going in  but i herd the power incres from able to breath more is crazy good it just burns alot more fuel faster so no more long trail rides just did not no if anyone on here has it done.  did no no if i had to run i big pipe to small one for like a holding tank for air. and yes all of u are smart that posted up here  keep them coming thank you

[FastestCub305]

opening up your airbox aint going to make that big difference in how much your gas lasts.

[crom A zone]

when u gotta let more air and fuel in it does

[JackL]

I think if you use silicone grease on the lids mating surface everything will be ok without all the hassle.

[Da_Mtg_Man]

I think if you use silicone grease on the lids mating surface everything will be ok without all the hassle.

Thats what I was gonna say. I just take marine grease and fill the little gap all the way around the lid of the airbox and you're good to go

[crom A zone]

now thats not like the gasket maker thats just regular grease

[Da_Mtg_Man]

I just use regular marine grease.

[Joedirt]

I have alway used clear window silicone on the lip of the airbox....gloop in on let it dry while clamped in place and you have a peelable gasket..2.99 a tube

[MudMan]

I used the rubber gasket maker crap on my airbox on my Foreman......works great....and I basically use my bike like a submarine   

[JackL]

now thats not like the gasket maker thats just regular grease

Yeah. RTV and silicone can sometimes stick so strong it is a big pain in the azz to replace the aircleaner.

I guess if you used some cheap stuff from Home Depot it would work like Joe Dirt says....just avoid the 3M 5200!!

[crom A zone]

k ill give that a try see how it goes  and jack when we gonna ride man?

[JackL]

k ill give that a try see how it goes  and jack when we gonna ride man?

I'm probably going to hit Macks this weekend at some point.

Might be flooded with all the rain. Hit me up if you guys are going anywhere. I wouldn't mind getting in some Holeyland rides.

[crom A zone]

the weekend shot got party after party but next weekend we should do holylands and show these people how men ride

[jrpro130]

seal up your airbox little man

[FastestCub305]

when u gotta let more air and fuel in it does

you seriously think that removing your airbox is going to waiste that much more gas to be even noticeable....LOL Its not

[jrpro130]

we tried it and it threw the jetting WAY off to have the airbox off.  He's got it all sealed up now professionally (or at least somewhat).

Got this straaaange ticking from the motor though

It's all good, run it till it breaks