C&R MOTORSPORTS SAND DRAGS FEB 24

[cutngrs]

THE FIRST RACE OF THE YEAR AT C&R MOTORSPORTS   FEB 24  WE WILL POST RULES  AND CLASSES  SOON 





WHOS YOU DADDY NOW  B@!CH

[attachment deleted by admin]

[cutngrs]

YOU WANT SOME MORE

[attachment deleted by admin]

[cutngrs]

COME GET SOME SUCKERS

[attachment deleted by admin]

[cutngrs]

YOU KNOW YOUR SCARED

[attachment deleted by admin]

[cutngrs]

THE GIANT KILLER

[attachment deleted by admin]

[dynodon]

Scared ?? Naw, Of what ?



A BIG ORANGE TURD !?!!?!?!!!?  Well, thats what Jeff said it was anyway

[cutngrs]

 THIS IS YOU NIGHTMARE

[attachment deleted by admin]

[dynodon]

Hey, I just Noticed something!!!
                        NICE paddles you got there  

[cutngrs]

ONE MORE I WILL  FINSH THIS THIS WEEK

[attachment deleted by admin]

[Smoknbanshee]

Hey, I just Noticed something!!!
                        NICE paddles you got there  

EXACTLY....he is slick.

[dynodon]

Hey, I just Noticed something!!!
                        NICE paddles you got there  

EXACTLY....he is slick.

Yeah, Notice how mine now has the " slicks" on it !?!?!?!?!?

[535banshee]

HE WENT THREW ALL THAT JUST TO GET A PIC WITH PADDLES ON IT.  WHAT FAG!!!!!!!!

[tribal_shee]

at least someones gonna get it running Thank God for Troy!  Remember cut, tune it right wink wink, don't want it to run too good

[535banshee]

ITS ALIVE!!!!!!!!!!!!!!! CANT WAIT UNTIL SUNDAY

[dynodon]

at least someones gonna get it running Thank God for Troy!  Remember cut, tune it right wink wink, don't want it to run too good

Hey Mike, remember this, I have an EGT for it !!!! So tuning the carbs wont be too hard......... wink, wink

[Hoosier Daddy]

does anyone have an out of frame pipe for a 250r i can borrow? 

[dynodon]

does anyone have an out of frame pipe for a 250r i can borrow? 

You flat track guys, sheeze!!!!!!

Naw Chris, i dont know of anyone that has one 

[tribal_shee]

at least someones gonna get it running Thank God for Troy!  Remember cut, tune it right wink wink, don't want it to run too good

Hey Mike, remember this, I have an EGT for it !!!! So tuning the carbs wont be too hard......... wink, wink

and.......... that means you wasted money on something you didn't need to spend money on! egt's are wayyyyyy overrated, kinda like putting dyna ignition on a bike. everybody always goes back to stock. Big D if you got fire and you got fuel it's gonna run, if it's not breaking up going down the track and it's smoking it's gonna be just fine, run it don't worry about all that computer bullshiot it will only drive you crazy!

[535banshee]

at least someones gonna get it running Thank God for Troy!  Remember cut, tune it right wink wink, don't want it to run too good

Hey Mike, remember this, I have an EGT for it !!!! So tuning the carbs wont be too hard......... wink, wink

and.......... that means you wasted money on something you didn't need to spend money on! egt's are wayyyyyy overrated, kinda like putting dyna ignition on a bike. everybody always goes back to stock. Big D if you got fire and you got fuel it's gonna run, if it's not breaking up going down the track and it's smoking it's gonna be just fine, run it don't worry about all that computer bullshiot it will only drive you crazy!

egt's are very good tuning tools. not only on jetting but gearing and clutch slipage. i am sorry but i am not going to just depend on smoke coming out of the pipe on a 8000.00 motor.
we used a laptop and  egt's at the track for info and what the bike is doing.
the graph will show rpm drop between shifts and egt numbers between cylinders. if one cylinder starts to show lower temp at a set rpm range you can go to the carb and check to see whats going on.
i have set carbs with a egt. if one slide is a little higher it will show in the egt. if on air and fuel mix.screw is a little diff. between cylinders it will show it. you can only tune so much by ear, if you want it perfect the egt is the way to go. i have seen bikes at the track that run great, but have a 100degree difference between cylinders. after Little tuning i have got them 5 to 10 degrees from each other. i agree you should not use one for topend tuning only. reading the ground strap on the plug should be done first. after you get it right , write down your numbers so you know what target you are looking for.
they they also have warning lights on them that you can set in case of a lean condition. imo a 380.00 part is cheap after you just spent 1000's for a motor.
ask terry and matt about their bikes. they run good and sound good but egt's way off of the bottom. 10mins later the egts are almost perfect and bike now runs and sounds better. hey everyone has what they like . i like like them but know alot of people that don't. dan hall doesn't like them and others in the sport. but they do agree they use them for the rpms to see rpm drop between shifts.

[tribal_shee]

 i understand where your coming from so, maybe it's not a waste of money for some people, but for the average person who builds a bike with 1800.00 motor like a 4 mill cub (cost= cylinders, crank, pistons) it's really not nessessary with what your working with. you could get it real close without one. An 8000.00 motor a little different cause you spend that kind of money on just a motor your pretty damn serious and it would be dynoed, fine tuned to the T, and have a computer hooked up to get every 1/16 of a hp out of it. Just my O.P.

Question is what ya gonna do when that little 4 mill runs wild on you! HEHEHEHE   How bout it Don   you'll be looking at the video after the race to see where he passes you and scratching your head instead of looking at the laptop

[535banshee]

i think when that happens i am going to run and hide

[tribal_shee]

I hear ya! That would kinda suck

[Smoknbanshee]

peek a boo.

[535banshee]

peek a boo.

now that was a good one

[dynodon]

All I got to say, IS BRING it !!!!!!!, Dont sing it , SUCKAS