HOW DO I SNORKEL A 2006 KODIAK 400 4x4 (COMPLETED)

Big Kev · October 15, 2006, 07:12:45 PM

Any ideas? Pictures?

Fox17 · October 15, 2006, 07:25:09 PM

go to home depot, buy some pvc (the flexible kind), go home, take the plastic off, unhook the stock snorkel from airbox, hook the pvc you just bought up to the airbox, and run it wherever you want it. that is how i am gonna build one.

Big Kev · October 16, 2006, 03:02:45 AM

The Kodiak is something different, a little harder. I think how I will do the transmission witch will be easy as f**k. its the intake i need help with really.

MachineDog · October 16, 2006, 03:25:19 AM

The tranny and intake are all just 3 tubes between 1.5 and 2" I think. Get a bunch of PVC and PVC glue and it should be easy.

Big Kev · October 16, 2006, 02:25:15 PM

The intake snorkal is part of the cap of the intake box, it goes up under the gas tank. so any clue?

Fox17 · October 16, 2006, 02:31:37 PM

take the stock intake tube off. it should unclamp from the air box. when that is off put a piece of pvc there and run it where ever you want it. what i dont know how to do is the tranny and all that. i can do the air box but i dont know where the other lines are.

Joedirt · October 16, 2006, 02:56:10 PM

Gotta watch the air fuel mixture when doing that Kodiak. The Stock lid has the snorkle attatched , so you will need a 3-2 inch rubber coupler. you will need to force the 3 inch part on the oblong stock snorkle...then probably cut the plastic around the gas Tank shroud and run your 2 inch PVC to the racks. That or seal off the stock airbock hole and make a new hole out the side or front and run your PVC. Stay with 2 inch or bigger.

MachineDog · October 16, 2006, 03:45:55 PM

We tend to take the stock snorkel that fits snug into the intake hole on the airbox, cut it up, and stick a tube into the small bit of the stock snorkel left. It works well. Remember to use the purple PVC glue on everything and silicone where it goes into the airbox.

Big Kev · October 16, 2006, 09:53:01 PM

Thanks for the info guys, I'll repost with a pic when it goes down

Big Kev · October 21, 2006, 06:14:46 PM

Well It is almost near the completion of the process

Parts:
Intake
1: 1'1/2 to 1'1/2 rubber coupler
1: 1'1/2 to 2' rubber coupler
1: 1'1/2 flex hose
3: 2' 90 degree pvc elbow
1: 2'pvc (2in)
1: 2' PVC (for snorkel)

Transmission
1: 2' to 2' rubber coupler
1: 2' PVC (for snorkel)
1: 2' 90degree pvc elbow

Big Kev · October 22, 2006, 06:04:25 PM

Joedirt · October 23, 2006, 01:53:10 PM

Do not for get to Snorkle the Belt Exhaust...

Kawa3 · October 23, 2006, 01:58:45 PM

Quote from: Joedirt on October 23, 2006, 01:53:10 PM
Do not for get to Snorkle the Belt Exhaust...

That is what I was going to say. You need 1 for Air Intake, 1 for Belt Exhaust and 1 for Belt intake.

Big Kev · October 24, 2006, 05:38:54 AM

Belt exhaust? Explain.

Joedirt · October 24, 2006, 06:18:35 PM

If you look at your belt Housing you will see the intake running from the housing to the front rack You found that...the Belt Exhaust runs out the back of the belt housing on the Right side ( as you sit on the quad). look under the plastic you will see an open ended Hard plastic tube running to the back of the Belt housing. That Too needs to be snorkled.

Big Kev · October 24, 2006, 10:24:44 PM

Alright now I think I'm done haha