Banshee back from dyno tuning

Started by TurboBanshee_kid, June 03, 2006, 01:57:04 AM

Previous topic - Next topic
Print
Go Down Pages1
User actions

TurboBanshee_kid

June 03, 2006, 01:57:04 AM
The Banshee was dyno tuned by TDR and is puttong out 50.5 H.P. to the rear wheeles.

I have a video of the Banshee running that i am going to put up!

Also tony put the T.O.R.S. eliminator kit on the banshee!


[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#1
June 03, 2006, 01:57:22 AM
 :)

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#2
June 03, 2006, 01:57:45 AM
 ;)

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#3
June 03, 2006, 02:21:42 AM
<a href='http://media.putfile.com/Yamaha-Banshee'; target='_blank'>Click here to watch 'Yamaha-Banshee'</a>
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#4
June 03, 2006, 02:23:52 AM
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#5
June 03, 2006, 03:57:39 PM
?
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

Hoosier Daddy

#6
June 03, 2006, 05:52:18 PM Last Edit: June 04, 2006, 01:55:32 PM by WareRacing07
Cant get your vid to work...

50 HP, do you have anythng else other than pipes?

What did tony charge you to dyno it? did he do any jetting?
BLISS Feed, Hay, and Race Fuels Zephyrhills, Fl
"Character is what you have when no one is looking"

TurboBanshee_kid

#7
June 03, 2006, 09:24:12 PM
it was $170 and he did alot more stuff for me but he treats me like family!
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#8
June 03, 2006, 09:26:16 PM
2005 engine that has a milled head,wiseco STD pistons, TDR HIGH PERFORMANCE REBUILT CRANKSHAFT trued to .001" and welded, Ricky Stator fly wheel and 200watt stator also timing plate is at +5 and the T.O.R.S. eliminator kit !

I am Running T-5's
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

Yamaha72

#9
June 03, 2006, 10:10:25 PM
Tony is a great guy, very friendly.... The last time I stopped by their he had a banshee being tuned on the dyno that was at 116 and he said he's seen a hair over 120 on his in-house dyno before, now thats arm-ripping power.... BTW nice shee.
2003 Yamaha Raptor 660

2005 Ford F-150

The Quad FaJa

#10
June 03, 2006, 10:51:39 PM
no Vid from the Dyno?

TurboBanshee_kid

#11
June 03, 2006, 11:57:33 PM
no sorry i was not there for the dyno of the bike!
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

The Quad FaJa

#12
June 04, 2006, 12:59:15 AM
Quote from: TurboBanshee_kid on June 03, 2006, 11:57:33 PM
no sorry i was not there for the dyno of the bike!
did you get the paper work of the run?

TurboBanshee_kid

#13
June 04, 2006, 01:37:45 AM
yes 50.5 H.P. good for not being ported or stroked!
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#14
June 04, 2006, 01:38:15 AM
That is to the rear wheel's
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

Smoknbanshee

#15
June 04, 2006, 01:54:19 PM
not bad results.  I would highly advice you to get cubby cylinders instead of definetly boring (does nothing basically) or stroking the bike.  cubby cylinders are putting out 90 HP on stock stroke. 
Team FBI (Florida Boy's Inc.)
A$$ Crack Racing
Choke on my Smoke!

Hoosier Daddy

#16
June 04, 2006, 02:00:58 PM Last Edit: June 04, 2006, 02:03:44 PM by WareRacing07
Quote from: TurboBanshee_kid on June 03, 2006, 09:24:12 PM
it was $170 and he did alot more stuff for me but he treats me like family!

So you paid 170.00, but it seems your not to sure what you got for that money..?

Do you have a graph?
What jetting did you end with?
BLISS Feed, Hay, and Race Fuels Zephyrhills, Fl
"Character is what you have when no one is looking"

TurboBanshee_kid

#17
June 04, 2006, 11:04:15 PM
yes and no. sould i find out?
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

Hoosier Daddy

#18
June 04, 2006, 11:15:25 PM
seeing how dyno time around here is 100.00 and thats as many pulls and jetting changes as you can make. it might be  good idea to find out what all was done, a graph would be good knowledge for you. I say the HP numbers sound right, I think a stock shee is 38ish.. although the crank you have dosent do anything for you (Hp wise) with pipes, timing, head milling & spot on jetting 55hp is very possiable.
For the riding you do, that would be where i would want to be at.
BLISS Feed, Hay, and Race Fuels Zephyrhills, Fl
"Character is what you have when no one is looking"
Print
Go Up Pages1
User actions
Other Florida sites of interest: www.PinballShark.com