Messages

Are they still around? Their website has been suspended and I dont get a response via email?

Any sport quads want to ride Rodman area Sat am?

North side of Ocala National Forest

Any sport quads want to ride Rodman dam Saturday?

Any sport quads want to ride Rodman dam Saturday?

I was riding Rodman Dam area Saturday. No smoke no fires.

Thanks guys.......I'm just going to buy the  5 gallon drums of Sunoco 110 going forward. I would rather not take any chances. 

I hear ya......

It did have a little pink tint to it. I'll drain the gas out tomorrow and buy a 5 gallon drum of the good stuff somewhere.

I sure hope my engine is ok. I rode for about 1.5 hrs today with this stuff.

TRX#9,

It was outside in a normal gas pump. Do you think it will be ok? I already put it in and rode Ocala today.   

Awesome - Thanks. I found race gas at the Gate on the corner or I95 and CR16. Its 110 octane 

Where can I get some high octane fuel?

Love it..........Mike does some great engine work

Not overly loud.....But not the quietest either......

Thanks

Yes, it was awesome. I moved to Florida from Arizona (Work transfer). So, I was spoiled with all the state land and riding areas. Plus, Glamis (Dunes) and Southern Utah were close    Only thing bad about AZ is the summer (Way Hot) . But, if you drive 1.5hrs north to Flagstaff the temps are usually in the 70s/80s with no humidty. Perfect reason to get away and camp for the weekend.

I really miss the Dunes in the winter.............

 

After ATP magic

2007 - Engine by ATP // Port and Polish // Valve work // CRF 450 Exhaust valve // Top End work // Pro Design Intake // Stage 2 cam // 14:1 ATP Piston // Rossier // Pro Taper // Nerfs

2004 - Engine by KBR and Mixxer // Port and Polish // JE 13:1 Piston // Rossier // Ron Wood Intake // Stage 2 cam // Universal bars

 

2007 - Engine by ATP // Port and Polish // Valve work // CRF 450 Exhaust valve // Top End work // Pro Design Intake // Stage 2 cam // 14:1 ATP Piston // Rossier // Pro Taper // Nerfs

2004 - Engine by KBR and Mixxer // Port and Polish // JE 13:1 Piston // Rossier // Ron Wood Intake // Stage 2 cam // Universal bars

Greetings all,

I picked my quad from ATP today and it smokes. I went out to Big Scrub for a while today and the quad has tons of power, from the bottom all the way to the top. My last quad, a 2004 TRX450R, had similar work done by the boys out west (Mixxer/KBR) and I was very happy. However, after the ATP magic on my 2007, my new one hauls even faster and pulls stronger.

I strongly recommend ATP for any aftermarket or engine mods.

Thanks a ton Mike and Melissa

Now I just need to save for some Walsh A-Arms and Fox Floats......Hopefully next month 

-Matt

Greetings all,

I picked my quad from ATP today and it smokes. I went out to Big Scrub for a while today and the quad has tons of power, from the bottom all the way to the top. My last quad, a 2004 TRX450R, had similar work done by the boys out west (Mixxer/KBR) and I was very happy. However, after the ATP magic on my 2007, my new one hauls even faster and pulls stronger.

I strongly recommend ATP for any aftermarket or engine mods.

Thanks a ton Mike and Melissa

Now I just need to save for some Walsh A-Arms and Fox Floats......Hopefully next month 

-Matt

Thanks Melissa. Yes, Mike called me first thing this morning. No worries, the peeps on here told me you guys were out of town. See you Friday 

Thanks all. I was getting a little nervous for a while. This is my 1st time working with ATP.

Great - Thx for the heads up

Who took 1st? Third?

Thanks

Matt

Anyone know how Jeremy Lawson did?