here is the pics of the stuff for my snorkel the total $$$$$ was around $45
im going to put it all together tomower and sunday but dont know when i can test it out
[attachment deleted by admin]
What the h*ll is that big a** bracket for??? :o
Thats so he doesn't have to cut a hole in his plastics. Looks like you got the right stuff. Remember to measure twice, cut once. I'll check here at lunch to see how your doin.
my momis giving me all this bs about me doing stuff around the house so i already put the lil tubs on the (carb,front dif,rear dif,back and front brakes ) and im going to seal it all tomower im going to take sum more pics in a few mins
im jealous lol, that thing is gonna look sick man ;)
ok wich one should i use i got both cuz i didint know wich one lol
[attachment deleted by admin]
ok here r the vent lines
[attachment deleted by admin]
my carb vent line
[attachment deleted by admin]
Use the U joint. Zip tie your vent hoses into the U(harder for the water to get in).
If your going to paint it do it before you attach it permanently, it's hard to do it right still attached. You can do your chores while the paint dries. ;)
By into the U I mean the shape of the U on the outside of the pipe.
[attachment deleted by admin]
Not my bike, just an example.
im not going to paint it im just going to leave it like that white
i take that back about me going through everything u can,i will go through almost everything u can ;)
ok i ran in to a problem it wont fit because of the head of the engine so its going to be like this ( 1 1/4 pvc then a 90 % elbow and then another lil pices of pvc then another 90 % turn and then another pvc pipe and then the 1 1/4 to 1 1/2 flex tube and then ill have it run up along my fender and then im going to cut the brackit and then drill it in to the plastics and tie strap it all to gether also i may snorkel out my moms recon but she dosint know yet also will the way i just said work
I used a set of 45's out the box to angle it over, but I also tucked it in the body. 90's should work just fine. I would increase pipe diameter right out the box. Just use 1 1/4 pipe to go thru the box hole then put a 1 1/4 to 1 1/2 adapter then your first 90.
[attachment deleted by admin]
oh cuz i already have the 1 1/4 it wont work if i do that
cuz im only using it when i go throw the hole and then out aftert the 90% im going to use the flex which is 1 1/2
When you get it attached check your plug after your first good test run. That will show you if your fuel to air mixture is still correct. Check your plug before you run it to see what it looks like before and after.
You should use a new spark plug o rwire bruch the one you have clean so you can easily tell if its rich or lean.
ok im going to get the 90 and then i will proble get a 45
post a pic of the dry fit
i alredy doid the dry fit but it im cuting the side of my plastics a lil bit so its not that much pushin on it
ok im dun its all snorkeled but if it gets water in it after a coupel of big holes im just goingt ot take it off and put back the stock one im going to bring it just in case
now the pics
[attachment deleted by admin]
more
[attachment deleted by admin]
more
[attachment deleted by admin]
more
[attachment deleted by admin]
more
[attachment deleted by admin]
the last one s
[attachment deleted by admin]
Looks good. Is it just me or did it switch sides? Test run?
Good idea about bringing your stock snork with you. Just keep checking for water in the box.
um no it didint switch side lol it looks like iit in the pic but no lol im going to try and test it out today
8)
[attachment deleted by admin]
ok cool thanks i have sum like taht im going to go to the store to get that one
Did you put some sort of plate under the bracket to reinforce the plastics?
what do u mean
ok i did a red neck paint job on it lol the pics r not all taht good cuz they r from my phone cam
[attachment deleted by admin]