Print Page - HomeMade HRC airbox lid and flap.

Title: HomeMade HRC airbox lid and flap.
Post by: Miami450R on March 08, 2007, 09:05:27 PM

Well im not really too good on $$ so instead of spending like 60 dollars or so on a actual HRC lid and flap , I modified my stock one to look and function like it,,,
this is what a Stock Lid looks like:
(http://450rheadquarters.invisionzone.com/uploads/monthly_02_2007/post-2158-1172367626_thumb.jpg)
thats my lid:
(http://i41.photobucket.com/albums/e290/civicfrk1/03-08-07_2012.jpg)
(http://i41.photobucket.com/albums/e290/civicfrk1/03-08-07_2018.jpg)

This is a HRC lid.I found this pic on 450r hq , Dont mind the burned part of it , but look at the hole , and flap...

(http://i5.photobucket.com/albums/y197/1BAD4FIFTY/Other%20450%20stuff/DSC01892-1.jpg)
By the way: for those who are wondering , I had to cut it because i rejetted my bike to a 180 main jet , and i would have to run open airbox , but i ride trails alot , so this gives me the air AND the protection I need :)

Not too Shabby Ehhh?

Title: Re: HomeMade HRC airbox lid and flap.
Post by: 4fittyr on March 08, 2007, 09:19:06 PM

nice engineering

Title: Re: HomeMade HRC airbox lid and flap.
Post by: The hyrbid kid on March 08, 2007, 11:30:05 PM

182 main jet no lid 8)

Title: Re: HomeMade HRC airbox lid and flap.
Post by: 1FasterBlaster on March 09, 2007, 12:38:32 AM

Mine has square hole cut out on the top with a silk screen cover.Breatheable, yet waterproof.

Title: Re: HomeMade HRC airbox lid and flap.
Post by: Miami450R on March 09, 2007, 06:06:37 AM

well i ran a 180 because i have a yoshi slip on and stock filter, it runs like its never ran before. I am EXTREMELY happy with it.

Title: Re: HomeMade HRC airbox lid and flap.
Post by: Ida_Mann on March 09, 2007, 08:07:16 AM

nice job,,,looks better than what you could buy.

Id@

Title: Re: HomeMade HRC airbox lid and flap.
Post by: TRX450R_Racer on March 09, 2007, 08:33:21 PM

Nice!

Title: Re: HomeMade HRC airbox lid and flap.
Post by: gearhead400 on March 10, 2007, 10:16:03 AM

Quote from: Ida_Mann on March 09, 2007, 08:07:16 AM
nice job,,,looks better than what you could buy.

Id@

i agree ;)

Title: Re: HomeMade HRC airbox lid and flap.
Post by: Young Gun on March 11, 2007, 12:07:53 PM

You could make those and sell them for cheap. What did you use to cut out the section?

Title: Re: HomeMade HRC airbox lid and flap.
Post by: Miami450R on March 11, 2007, 12:09:51 PM

I used my dad's Compressor with the Hi-speed cutter (disc).

then i used a little wool brush tip with the compressor , and smoothed out the edges and rough spots. lol.

Thanks.

ATV Florida Forum

General => Photo Gallery & Videos => Topic started by: Miami450R on March 08, 2007, 09:05:27 PM