Zilla got a new pipe....

Started by Old_School, October 16, 2005, 09:08:49 PM

Previous topic - Next topic

Old_School

Finally got rid of my junk FMF pipe for this inframe drag pipe. It's custom made by The Power Pros out in CA. For those that knew the situation and fiasco in getting this d**n thing from the vendor I wanted to show it off. Enjoy!  ;D  -Mark





90' LT500R Quadzilla
Breathing fire and crushing cities

92' LT250R Quadracer
Some stuff done. 75+mph (Sold)

"When this baby hits 88 mph, you're gonna see some serious $%#!" - Christopher Lloyd

xtremeraptor

FOR THOSE WHO BELIEVE NO EXPLANATION IS NECESSARY...................FOR THOSE WHO DO NOT NONE WILL SUFFICE

LakeMaryKid

Well.......was it worth the wait though?
2003 KFX 400
1994 F-150 - 12" SAS 38.5 Boggers
2007 F-150 Supercrew FX4 Luxury
2004 14' Mirrocraft

Yota

nice looking 500, gotta love the gold tooth
yeah about that

Old_School

Quote from: LakeMaryKid on October 16, 2005, 10:23:37 PM
Well.......was it worth the wait though?

Yes.  ;D But now my motor is dying for a bigger carb. This pipe pretty much maxed out my stock carb.  But it still hits the powerband hard while starving for fuel in the mid/high rpms.  Thanks guys.  -Mark
90' LT500R Quadzilla
Breathing fire and crushing cities

92' LT250R Quadracer
Some stuff done. 75+mph (Sold)

"When this baby hits 88 mph, you're gonna see some serious $%#!" - Christopher Lloyd

Honda250ex

'03 F-250 7.3L
Lawn Service 4Sale w/equipment!!
98% of all ATV'ers FLOOR their quads if your the 2% then your GGGGGGGGGGGGGG@@@@@@@@@@yyyyyyyyyyyyyyy

Nightbreed

Lookin good.
But they put the pipe on the wrong side of the quad ! ;) HA HA

What size carb is on there, I might have a keihin around here that would work.

Mike
What doesnt kill you, Makes you stronger!

Old_School

Quote from: Nightbreed on October 17, 2005, 10:00:27 AM
Lookin good.
But they put the pipe on the wrong side of the quad ! ;) HA HA

What size carb is on there, I might have a keihin around here that would work.

Mike

Mike, Thanks.  It's the stock 38mm Mikuni flat side carb. I'm already at a 480 main and the needle has only one notch left and it's still lean in the mid range and a little lean in the low end. I have a idle jet that's 37.5 (stock was 20... I think)  I just done think that the OEM carb can handle what I have done.  Doesn't Keihin have a different set of numbers for jet sizes?

-Mark
90' LT500R Quadzilla
Breathing fire and crushing cities

92' LT250R Quadracer
Some stuff done. 75+mph (Sold)

"When this baby hits 88 mph, you're gonna see some serious $%#!" - Christopher Lloyd

Mrs.Nightbreed

Good to see you got it! He must have seen our atvfl threat to send his mail away  >:D

Nightbreed

The keihin carbs do go by different jet sizes. I have a 40mm smooth bore here that should probably work for you.

I would think that a 40mm with around a 190 to a 200 main jet and around a 60 pilot should work for you.

mike
What doesnt kill you, Makes you stronger!

lt2301987

that bike is so sick that was and still is my favorite atv.
300ex mine
lt230e dads
5.5go kart

Old_School

Quote from: Nightbreed on October 17, 2005, 04:17:38 PM
The keihin carbs do go by different jet sizes. I have a 40mm smooth bore here that should probably work for you.

I would think that a 40mm with around a 190 to a 200 main jet and around a 60 pilot should work for you.

mike

Well it's got some other goodies than just the pipe. The keihin carb, is it a flat side or round carb? 

lt230- Thanks.  -Mark
90' LT500R Quadzilla
Breathing fire and crushing cities

92' LT250R Quadracer
Some stuff done. 75+mph (Sold)

"When this baby hits 88 mph, you're gonna see some serious $%#!" - Christopher Lloyd

Nightbreed

What doesnt kill you, Makes you stronger!

Other Florida sites of interest: www.PinballShark.com