Banshee throttle ?????????

Started by TurboBanshee_kid, May 03, 2005, 06:36:57 PM

Previous topic - Next topic

TurboBanshee_kid

I have the stock thumb throttle on my banshee and my throttle cable runs in to the T.O.R.S. on top of my carbs. Now on my friends banshee he has the twist throttle and his throttle cable goes straight into the top of the carbs without the T.O.R.S.(THROTTLE OVER RIDE SYSTEM)

1. WHAT IS THE T.O.R.S.  ???

2.If he wants to remove the twist and put the stock thumb throttle on will he need the T.O.R.S. ???
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

Nightbreed

He will eaither have to put a TORS back on, or there are several companies out there that sell the TORS eliminator caps. Depending on the type of carb cap that he currently has on the top, he might be able to use them and put the thumb throttle cable back on.

Can you get any picks of the caps on top of the carbs?

Mike
What doesnt kill you, Makes you stronger!

TurboBanshee_kid

Also if i run it in to my caps will i get more power or somthing like or low end power.
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

DS650

No gains,Your throttle wont get stuck at WOT though.
~~~~~~~~~~~~~~~~~
2004 Grizzly 660-Stock
2001 Banshee-Mods  
~~~~~~~~~~~~~~~~~

Smoknbanshee

definelty no power gain...basically just cleans up the look and gives you more room.  
Team FBI (Florida Boy's Inc.)
A$$ Crack Racing
Choke on my Smoke!

TurboBanshee_kid

this is my t.o.r.s on the banshee
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

these are my t.o.r.s

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

my friend t.o.r.s he has the twist throttle

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

my friend's t.o.r.s he has the twist throttle


[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

my friend's t.o.r.s he has the twist throttle  


[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

Nightbreed

#10
You should be able to get a thumb throttle cable for a non TORS system and put it right on those caps.

Let me know if you need any help.

Mike
What doesnt kill you, Makes you stronger!

TurboBanshee_kid

New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs