The Banshee project has come to the END!!!!!!!!!!!!! Alots of Pic's

Started by TurboBanshee_kid, June 04, 2006, 03:10:45 AM

Previous topic - Next topic
Print
Go Down Pages1 2 3
User actions

TurboBanshee_kid

June 04, 2006, 03:10:45 AM
As most of you know i have done alot of work on my banshee will hear is the hole story!


[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#1
June 04, 2006, 03:11:16 AM
This photo is from when I first bought the banshee a year and a half ago and a few thousand dollars richer! LOL

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#2
June 04, 2006, 03:11:52 AM
This photo is when I had taken the plastics off for it's first re-bill, little did I know it would take a year to finest!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#3
June 04, 2006, 03:12:22 AM
This photo was taken just after I had taken the lights off!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#4
June 04, 2006, 03:12:52 AM
This photo is when I had taken out the engine! At this time I did not know I needed a full engine rebuild! Dam that was a lot of money! But well worth it!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#5
June 04, 2006, 03:13:15 AM
Almost to the bear frame!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#6
June 04, 2006, 03:13:44 AM
A VIEW OF THE REAR!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#7
June 04, 2006, 03:14:12 AM
The Bear frame ready for powder coating! It was a lot of work getting all that paint off!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#8
June 04, 2006, 03:14:47 AM
The is a Photo of when I got my engine back from TDR, Tony the shop owner installed 2005 cylinders that where on stock bore and just needed a hone also he put new wiseco STD pistons in it and also put a TDR HIGH PERFORMANCE REBUILT CRANKSHAFT trued to .001" and welded and a Ricky Stator fly wheel and 200 watt stator also the timing plate is at +5.

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#9
June 04, 2006, 03:15:26 AM
This is a photo of when I got the Banshee all back together! Little did I know I needed new A-arm's upper and lower! That sucked!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#10
June 04, 2006, 03:15:59 AM
Another photo right after I put some more things on the banshee that same day!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#11
June 04, 2006, 03:16:39 AM
This is a photo of when I put the $250 UM Nerf Bars on the banshee! They are great!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#12
June 04, 2006, 03:17:07 AM
This photo is of when I got my bike back form TDR, Tony dyno tuned it for me! It dyno 50.5 H.P. to the rear wheel's witch is not to bad for not being ported or stroked!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#13
June 04, 2006, 03:17:41 AM
Also he put the T.O.R.S. eliminator kit on the banshee for me.

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#14
June 04, 2006, 03:18:13 AM
This photo is right after I put the flywheel cover back on and the plastics and got the banshee back to a 100%!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#15
June 04, 2006, 03:18:46 AM
Another view of the Banshee at 100%!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#16
June 04, 2006, 03:19:13 AM
And Another!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

TurboBanshee_kid

#17
June 04, 2006, 03:21:03 AM
So after it was all said and done My Banshee project has taken one year and a few thousand dollars to complete put in the end it was all worth it! The banshee has all new stuff on it and is 10 times better then stock! And I'm loving it!

[attachment deleted by admin]
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

rubicon500kid

#18
June 04, 2006, 03:25:38 AM
what happind to the works front shocks y do u got the stock 1 back on

btw it looks nice better then what it was when i wnet and bought ur old 300 LOL
also what happind to the 550 u had ?
DROP & DESTROY
87 s10 2/3 soon to be bagged
85 honda 110 atc(22" bearclaws & snorkeld)
01 kx 125 (pc pipe,tag bar's,pro racing rear rim,some lil other stuff
I hate it when you microwave something, then you start eating it, and it's cold in the middle...makes me wanna punch a

TurboBanshee_kid

#19
June 04, 2006, 03:30:20 AM
The predator is in the shop! It is taking along time!

The works shocks were to big they where the the flat track shocks for the predator.

Thank you me and you are going to ocala soon OK!
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

rubicon500kid

#20
June 04, 2006, 03:33:20 AM
ok let me know bro i sold my 400ex but will have a new bike soon 4x4 tho but 750cc lol 
ill have a 450r or a banshee in 3-6 months tho (how ever long it takes to sell our house )
DROP & DESTROY
87 s10 2/3 soon to be bagged
85 honda 110 atc(22" bearclaws & snorkeld)
01 kx 125 (pc pipe,tag bar's,pro racing rear rim,some lil other stuff
I hate it when you microwave something, then you start eating it, and it's cold in the middle...makes me wanna punch a

TurboBanshee_kid

#21
June 04, 2006, 03:37:19 AM
do you have a bike now!
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

rubicon500kid

#22
June 04, 2006, 04:00:12 AM
recon and a rancher lol but ill have my new bike soon
DROP & DESTROY
87 s10 2/3 soon to be bagged
85 honda 110 atc(22" bearclaws & snorkeld)
01 kx 125 (pc pipe,tag bar's,pro racing rear rim,some lil other stuff
I hate it when you microwave something, then you start eating it, and it's cold in the middle...makes me wanna punch a

TurboBanshee_kid

#23
June 04, 2006, 12:52:56 PM
Why did you sell the 400ex?
New to the Engine 421cc Cheetah Cubs that are fully race ported, Hot Rods 4mm Stroker Crank, Ricky Stator fly wheel and 200watt stator also timing plate is at +5, NOSS Head with 17cc domes, V force 3 reeds and 36mm MIKUNI Flat Slide carbs

jonnyyellow

#24
June 04, 2006, 04:29:50 PM
Quote from: TurboBanshee_kid on June 04, 2006, 12:52:56 PM
Why did you sell the 400ex?

yeah uhh.. didnt you just get it?
lol
Print
Go Up Pages1 2 3
User actions